VIKEFON WiFi Repeater’s Feature
1.Exclusive high quality wall-to-wall technology ensures that the repeater coverage is not blocked.
2.New high-quality chip that provides stable 2.4GHz network service with network speeds up to 300Mbps.
3.Built-in software upgraded, super simple setup steps, eliminate the cumbersome troubles for consumers.
Q&A
Q1. Can’t connect to internet after finished setting ?
A1. Please check whether you enter the same password as your router, and check is there any special characters in it, such as ~!@#$%^&*(). If yes, please change your router password. Repeater can not identify special characters.
Q2. How to reset the repeater ?
A2. Please long press the reset button for 10 seconds under powered. ( NOT WPS button, the reset button is at the side)
Product Features:
1. 2.4GHz 300Mbps high transmission speed improves wireless coverage in all WLAN networks.
2. Access to the Internet for computers located on the edge or outside of the range of your access point.
3. Provides one 10/100Mbps Auto-Negotiation Ethernet LAN ports.
4. Complies with IEEE 802.11n, IEEE 802.11g, IEEE 802.11b standards.
5. Provides up to 300Mbps transmission rates.
6. Support 2.4 GHz WLAN networks.
7. Maximum WLAN security with WPA2, WPA and WEP (128/64).
8. Software wizard for simple setup.
9. Support Wireless Repeater Mode and Standard AP Mode.
10. Integrated Dual-Antennas for higher stability.
11. Correct the language and the stablility of signal, revise default reboot.
12. Former version need reticle to reboot,but now do not need.
13. Smart LED status indicator helps you to find the best location to place the range extender.
14. Outdoors 300Mbps, Indoor 100Mbps (According to the Actual Environment Change).
Specifications:
Color: Black / White
Product Type: WIFI Repeater
Plug Type: UK / EU / US /AU Plug
Voltage: AC 110-240V
Frequency Range: 2.41-2.48GHz
Networking Cable Length: approx. 1m / 37.37in
System Requirements:
1. WLAn access point/client according to IEEE 802.11n/g/b.
2. The WLAN client must support at least WPA encryption standard.
3. WLAN access point and the WLAN client with automatic IP address assignment(DHCP).
4. Forwarding of IPv4-bassed protocols/Address Resolution Protocol.
5. The network name (SSID) of the WLAN access point must be set to *visible*
Package Content:
1 x Wireless Wifi Repeater (US/EU/UK/AU Plug)
1 x RJ-45 Networking Cable
1 x Installation Manual
Note:Because the AU plug will be cheaper, so lots of people buy it,but its can not use in their country after receive the AU plug.So please confirm if it can use in your country when you buy it. The AU plug only can use for Australia normal. Follow was AU plug real photos.
Installation:
1. please reset the device for better connection.
a: Reapter mode:
1.1 find the wifi, connect it,
![]()
1.2 then enter the website: 192.168.11.1, user name and passwords
:admin, login in
![]()
![]()
1.3 Choose repeater mode, and choose one wifi, please note: wifi
must be 2.4G, can’t be 5g. If you are not sure your wifi is 2.4G or 5G, or support both, please enter your router website, which can be found on the opposite side of the router, for example:
enter and find the wireless setting, close the switch of wifi Multi-frequency in one, only turn on 2.4G wifi.
![]()
1.4 then, back to the repeater mode, find your wifi and input the wifi code, after setting well, please connect the EXTEND SSID WIFI , input the wifi code, it will be working , like below:
![]()
![]()
B. AP mode:
follow the above 1.1-1.2 and choose AP mode, choose encryption or not encryption, if encryption, please input the code you want to set, like below:
![]()
then, use a network cable to connect the repeater and your router, then connect the wifi of the device again, and it will be working.
IF you are not in Australia or New Zealand, Please do not buy AU plug ,otherwise we will not refund. Thanks.
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
