Special Note:
Dissatisfied after receiving the goods, free returns within 15 days
433Mhz Universal Wireless Remote Control Switch DC12V 4CH relay Receiver Module and 4 channel RF Remote 433 Mhz Transmitter
Application areas:
Products can be used in homes, farms, factories, offices, laboratories, supermarkets and so on.
Remote control garage door Electric door house door shutter door expansion door gate door road gate
Remote control Electric curtain Water pump Fan Lamp LED light bulb ventilation device Signal transmission
Remote control motor positive and negative rotation motor switch
Order Model 1:
1Piece KR1204-4 and 5 Remote Controls
Details:
Receiver Switch Module (KR1204-4): 1 Piece with Plastic Shell
Remote Control: 5 Pieces with Battery
Order Model 2:
1 Piece KR1204-4 and 4 Remote Controls
Details:
Receiver Switch Module (KR1204-4) : 1Piece with Plastic Shell
Remote Control : 4 Pieces with Battery
Order Model 3:
1Piece KR1204-4 and 3 Remote Controls
Details:
Receiver Switch (KR1204-4): 1 Piece with Plastic Shell
Remote Control: 3 Pieces with Battery
Order Model 4:
1Piece KR1204-4 and 2 Remote Controls
Details:
Receiver Switch Module (KR1204-4): 1 Piece with Plastic Shell
Remote Control: 2 Piece with Battery
Order Model 5:
1Piece KR1204-4 and 1 Remote Controls
Details:
Receiver Switch Module (KR1204-4): 1 Piece with Plastic Shell
Remote Control: 1 Piece with Battery
The way of Circuit Connection:
Please Note: the Receiver Switch Module part number KR1204-4 have 3 ways of working mode.The OUTPUT signal have 2 Voltage Level. It decided by the IMPUT of the COM pin.
OUTPUT mode 1:
Connect the COM to the Power Supply by DC12V, the Output pin will create DC12V Signal. Please check below diagram for better understanding.
OUTPUT mode 2:
Connect the COM pin with any other Additional Power Supply,the output will create the same Voltage signal as the Additional Power Supply. it can be Direct Current or Alternating Current. Decided by the Additional Power Supply.
BUT, Please note: the additional Power Supply should be in the range of the Receiver Switch Module-(DC5-12V, AC 85-240V).
Please check below diagram for better understanding.
OUTPUT mode 3:
Mix work mode: You can also make 2 channel work under the DC output mode, and 2 with the AC output. Please check below diagram for better understanding.
Transmitter (remote control) technical parameters:
Model: KT01-4
Operating frequency: 433 9.2MHz
Battery model: 27A12V (with battery)
Material: PVC
Button: 4 buttons
Size: 50 mm × 30 mm × 9 mm
Working voltage: DC: 12V.
Working current: <25mA
Transmission power: + 13dbm
Frequency wind resistance: ±0.2MHz
Modulation method: ASK (AM)
Coding type: learning code 1527 fixed code (2262)
Transmission distance: 15-80 meters
Weight: 35 grams
Product specifications:
Receiver (KR1204) electronic characteristics:
1. Input voltage: DC12V
2.Output voltage: determined by the voltage connected to the common port (COM)
(1) DC5V-12V.
(2) AC85-240V
3. Code: EV1527
4. Loop current limit: 5A
5. Quiescent current: 5mA
6. Working frequency: 433Mhz
7. Receive sensitivity: -104dBm
8. Function options: instantaneous / switching / latching
9. Modulation mode: ASK
10. Matching mode: intelligent learning code
11.Receiver matching: 35 pieces (remote control)
12. Maximum power: 2000 watts
13. Receive signal distance: 50-100 meters. (open land)
14. Channel: 4 channels (4 devices can be
connected)
15. Scope of Application: all kinds of electric doors, windows, lifting equipment, gates, lifters, LED lamps and lanterns
Decorative switch, motor forward and reverse rotation, motor switch, industrial control, household appliance control, lighting control, window
Curtain control, telephone remote control, indoor and outdoor remote control, anti-theft alarm, environmental monitoring, HVAC control, shopping malls, home anti-theft, communication security and other fields
Pin function:
+ V: positive input
GND: negative input
1. KC1 Normally Closed Relay (NC)
2. KC1 Relay General (COM)
3. KC1 normally open relay (NO)
4. KC3 Normally Closed Relay (NC)
5. KC3 Relay General (COM)
6. KC3 normally open relay (NO)
7. KC2 Normally Closed Relay (NC)
8. KC2 Relay General (COM)
9. KC2 normally open relay (NO)
10. KC4 Normally Closed Relay (NC)
11. KC4 Relay General (COM)
12. KC4 normally open relay (NO)
When the relay is energized, NO and COM connected.
Please find the Learning Key of the Receiver Switch Module by checking below photo
1. LED lights
2. Learning button
4 keys (A, B, C, D) remote control and DC12V4 channel receiver operation method:
Step 1: Clear the original memory in the receiver
Press the Learn button on the receiver 8 times and wait for the LED bulb on the receiver to flash 5 times. The code will be cleared.
After clearing the code, the entire remote will no longer work.
Step 2: The 4 button (A, B, C, D) remote control can be configured in 7 modes:
1: Instant mode:
Press the learning button on the receiver once to enter the switch setting mode. .
Wait until the LED indicator lights up and enters the learning state.
Press the “A” button on the remote control and then press the “B” button. The LED bulb on the receiver board flashes 3 times and then goes out.
Successful learning. The coding was very successful.
Press the “A” button on the remote control and the relay turns on. Release the “A” button on the remote control and the relay will turn off.
Press the “B” button on the remote control and the relay will turn on. Release the “B” button on the remote control and the relay will turn off.
2: Self-locking mode:
Press the Learn button on the receiver twice to enter the switch setting mode.
Wait until the LED indicator lights up and enters the learning state.
Press the “A” button on the remote control and then press the “B” button. The LED bulb on the receiver board flashes 3 times and then goes out.
training. The coding was very successful.
Press the “A” button on the remote control and the relay turns on. Then press the “A” button on the remote control and the relay turns off.
Press the “B” button on the remote control and the relay will turn on. Then press the “B” button on the remote control and the relay turns off.
3. Lock mode:
(A), clear the memory code in the receiver again:
Press the Learn button on the receiver 8 times and the code will be cleared.
After clearing the code, the entire remote will no longer work.
(B) Press the “Learning” button on the receiver three times. Enter the switch setting mode.
Wait until the LED indicator lights up and enters the learning state.
Press the “A” button on the remote control and then press the “B” button. The LED bulb on the receiver board flashes 3 times and then goes out.
training. The coding was very successful.
Press the remote control button “A”, the relay is connected (start operation), then press the remote control button “B”, the relay is disconnected (stop operation). Another channel is open (beginning to work)
Press A to stop. B is open. Press B to stop and press A to open. Convert to each other.
4. 2CH instant + 2CH switching:
Press the four times of the learning button on the receiver board (the LED on the receiver board will simultaneously signal), then press any of the remote buttons to send three signals through the remote control LED to inform the setting.
5. 2CH instant + 2CH latch:
Press the learning button on the receiver board five times (the LED on the receiver board will simultaneously signal), then press any of the remote buttons, and the LED will be sent three times through the remote control to signal the setting.
6. 2CH Toggle + 2CH Latch:
Press the learning button on the receiver board six times (the LED on the receiver board will signal at the same time), then press any of the remote control buttons, and the LED indicator from the remote control will send three times to signal the setting success.
7. 2CH latch + 2CH latch:
Press the seven times learning button on the receiver board (the Led indicator on the receiver board will simultaneously signal), then press any of the remote control buttons, and the remote control LED will signal three times to indicate that the setting is successful.
3. Return rule:
Non quality problems will not be adjusted or refund. Please check product information carefully before placing an order to avoid unnecessary loss.When the product quality problems occur, please consult the customer service for more details first.
Dear friends!
If you are satisfied after receiving the goods, please give me five stars. And share photos!
If you are not satisfied and have a problem. Welcome to ask questions.
1. If the delivery is not correct, please contact us within 48 hours after delivery. We will arrange to provide the correct item or refund all payments.
2. For defective products, please take a photo or video. After confirmation, we will resend or refund.
Please do not dispute, the dispute is not friendly or the best solution.
Please trust me,
We will definitely help you out. satisfy you
Please click on me and you will know more.