Features:
1. Lightweight and portable, it weighs only 20 grams without battery.
2. The new and highly integrated Crazybee F4 Lite flight controller integrates OSD, Dshot ESC, 2.4G SPI receiver, 5.8G VTX, etc.
3. 0802 motor KV19000/25000KV motor with 31mm propeller, to provide you with powerful flying power.
4. Crazybee F4 Lite version flight controller supports 1S lithium battery (lihV). Integrated injection molding Tiny Whoop structure.
5. 1S indoor whoop traversing machine, with 0802 motor, strong power
6. Support Betaflight tuning, multiple flight modes.
7. Frskys and Flysky version highly integrated motherboards integrate OSD, Dshot ESC, 2.4G SPI receiver, 5.8g 25mw 40CH VTX.
8. Integrate Betaflight OSD function, keep track of the flight voltage and receiver signal at any time, and fly more calmly.
9. The VTX comes with Smartaudio function, you can adjust the flight control parameters through the OSD, adjust the flight control PID, and adjust the VTX frequency point parameters.
10. The tilt angle of the camera is adjustable.
Description:
Mobula6 is a highly integrated ultra-small 1S indoor 65mm wheelbase brushless Whoop traversing machine.
Specifications:
Brand: Happymodel
Wheelbase: 65mm
Size: 80mm*80mm*37mm
Weight: 20g
Receiver option:
Internal SPI Frskys version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Motor:
Mode: SE0802 19000KV or KV25000
Configu-ration:9N12P
Stator Diamter: 8mm
Stator Length: 2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
Weight(g): 1.9g
No.of Cells(Lipo):1S only
Propellers:
Gemfan 1219-3
Center Thickness: 5mm
Prop Disk Diameter: 31mm
Center Hole Inner diameter:1.0mm
Weight: 0.28g
Flight controller:
(Frskys SPI RX version) CRAZYBEE F4 Lite Frskys version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frskys/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC:
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
Onboard Frskys SPI D8 receiver Version:
SPI BUS receiver Frskys D8 compatible
Compatible Non EU transmitter D8 model
Channels: 8ch
Failsafe support
No ground interference (Transmitter and receiver 1 m from the ground): 100m~200m
Onboard Flysky SPI receiver Version:
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference (Transmitter and receiver 1 m from the ground): 100~200m
Failsafe support
Onboard 5.8g VTX:
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Runcam Nano3:
Model: RunCam Nano3
Image Sensor: 1/3″ CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: PAL/NTSC Non Switchable
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: [email protected]
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V [email protected]
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm
Lipo Battery:
Capacity: 300mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Size: 57mmx12mmx7mm
Weight: 8g
Connector: PH2.0
Package Included:
1* Mobula6 1S 65mm whoop Drone Frame
1* SPI Receiver
4* SE0802 KV19000 or KV25000 brushless motor
1* Gemfan 1219-3 Propellers(4cw+4ccw)
1* Runcam Nano3 1/3 CMOS 800TVL camera
1* 5.8G 25mw 40ch vtx (Flight controller built-in)
4* 1S 300mah 30C LiHV Battery
1* 1S Lipo/LIHV USB Charger
1* Propeller disassemble tool
Notes:
1. Please allow 0-1 inch error due to manual measurement. Thanks for your understanding.
2. Monitors are not calibrated same, item color displayed in photos may be showing slightly different from real object.